Mell What wood does Mossberg use?
Mossberg uses birch and walnut. That one is birch. You can sand it down to raw wood, then apply sanding sealer to keep the stain from turning out blotchy.
Should I refinish my M1 Garand stock?
If you are collecting M1s, you would never refinish one. On the other hand if you want to build an accurate rifle, by changing the barrel and stock, you may want to refinish it. Cleaning up a stock for any M1 would preserve the wood. That would not decrease the value as long as you do it properly.
How much should you sand before staining?
On most raw woods, start sanding in the direction of the grain using a #120-150 grit paper before staining and work up to #220 grit paper. Soft woods such as pine and alder: start with #120 and finish with no finer than #220 (for water base stains) and 180 grit for oil base stains.
Do you have to sand wood before staining?
The best way to stain wood is to prepare the wood surface by sanding it with a sanding block or orbital sander. Sandpaper with a lower grit number will make wood rougher, allowing more stain to absorb and create a darker color. Start with 120-grit sandpaper on refinished pieces.
What can I put on the M1 Garand stock?
As to the M1 Garand Rifle, it is believed that the original manufacturer’s finish utilized boiled linseed oil into which the stocks were dipped and then dried. Subsequently, what might be called boiled tung oil was used instead.
What is the difference between tung oil and linseed oil?
They’re both plant-based oil finishes that penetrate and saturate the wood grain. Linseed oil carries a slight yellow tint, whereas tung oil dries to a clear finish. Tung oil creates a harder, more durable finish than linseed oil. Tung oil is more water-resistant than linseed oil.
What happens if you don’t wipe off wood stain?
If the excess stain is not wiped off, the stain will not dry properly or completely and any finish applied over it will not dry either. To improve the grain definition, apply an oil stain after the dye has dried — or over the sealer coat — and wipe off the excess. …
What happens if you don’t seal stained wood?
A: If you don’t apply some kind of sealer the wood will be dried-out and lifeless. When you rub stain into wood, it brings out the grain pattern and gives the wood a more dramatic look. The final step in staining wood is to wipe off any excess, so the process leaves nothing behind.
What happens if you don’t sand before restaining?
A lot of folks make the mistake of sanding to either too fine of a grit or not fine enough before applying stain. Too fine and the wood won’t be able to accept the stain. Too rough and the wood will be very dark almost to the point of being black.
What happens if you dont sand before staining?
Make sure you sand the wood well before applying stain. Any scratches will be enhanced by stain. Sanding will also help open up the pores of the wood so that they can absorb stain better. Make sure you remove any sanding dust from the surface.
What’s the difference between a Mossberg 505 and a bantam?
The new Model 505 Youth shotgun, introduced in 2005, is similar to the Bantam but scaled down further. The 505 has a 12-inch (30 cm) LOP buttstock (compared to a standard model’s 14 inches or 36 centimetres, or a Bantam’s 13 inches or 33 centimetres), a 20-inch (51 cm) barrel, and a four-shot magazine tube.
What’s the difference between Mossberg 500 and 535?
The Model 535, new for 2005, is similar to the Model 500, but with a lengthened receiver that can fire 3.5-inch (89 mm) shells, in addition to 2.75-inch (70 mm) and 3-inch (76 mm) shells. The 535 is a less expensive alternative to the Mossberg 835 Ulti-Mag, but the 535 lacks the 835’s overbored barrel.
Do you need a heat shield for a Mossberg 500 Bantam?
A heat shield and bayonet lug are required for military 3443G Type I riot shotguns, and some 590A1s are so equipped. The 590A1 heat shield, p/n 16335P, is available for purchase from Mossberg for about the same price as the 500 heat shield. Mossberg 500 Bantam, with 24-inch (610 mm) barrel. Note shorter stock and forend than standard model at top.
What kind of shotgun is Mossberg law enforcement?
Mossberg shotguns currently designated “law enforcement models” are 590A1s. 590A1s differ from other 500/590 shotguns, in that they have heavy barrels, metal trigger guards, and metal safeties. 590A1s are available in 14-inch (36 cm), 18.5-inch (47 cm), and 20-inch (51 cm) barrels.